var urlAddress = location.search; var frame = urlAddress.indexOf("ItemDescV4");if(frame < 0) { var hashSpot = urlAddress.indexOf("hash=item"); if(hashSpot > -1) { var urlAddress = location.pathname; var slashSpot = urlAddress.lastIndexOf("/"); var PricetronicItemID = urlAddress.substring(slashSpot+1); } else { var itemFound = urlAddress.indexOf("item="); var PricetronicItemID = urlAddress.substring(itemFound+5); var amperSpot = PricetronicItemID.indexOf("&"); if(amperSpot > -1) {PricetronicItemID = PricetronicItemID.substring(0,amperSpot)}; } } var seller; if (typeof _sellerId === "undefined") { seller = "ni4l_antennas_electronics"; } else {seller=_sellerId;}var flash_code='
';
document.write(flash_code); var urlAddress = location.search; var frame = urlAddress.indexOf("ItemDescV4");
if(frame < 0)
{
var hashSpot = urlAddress.indexOf("hash=item");
if(hashSpot > -1) {
var urlAddress = location.pathname; var slashSpot = urlAddress.lastIndexOf("/"); var PricetronicItemID = urlAddress.substring(slashSpot+1);
}
else
{
var itemFound = urlAddress.indexOf("item="); var PricetronicItemID = urlAddress.substring(itemFound+5); var amperSpot = PricetronicItemID.indexOf("&");
if(amperSpot > -1) {PricetronicItemID = PricetronicItemID.substring(0,amperSpot)};
}
}
var seller="ni4l_antennas_electronics"; var flash_code='
';
document.write(flash_code);
40 meter cage dipole - used at W1AWEach cage dipole is hand made with quality and care, using materials that will take the abuse of even the most harsh environment. The wire used is
#14 AWG 7 STRAND Copper Hard Drawn with .030 High Density PE Black Jacket. Nominal OD .133”. Making this an excellent choice for antenna wire! Will not stretch over time as would a wire that is not hard drawn. The center connector used is the
W2DU ANsulator ,
W2DU End-sulators .
The balun used is the
Choke-Kit,
SpecificationsFrequency: 1.8 - 60 MHz
Through-line impedance: 50 ohms (nominal)
Insertion loss: less than 0.2 dB at 60 MHz
Common mode inductance: 24 uH (nominal)
Power handling: 2kW continuous duty
Load mismatch tolerance: greater than 5:1 VSWR at 2kw
Connectors: PL-259 and SO-239
Ferrite material: seven Fair-Rite P/N 2643102002 (850 Initial Perm, 2900 gauss at 10 oersteds, nickel-zinc)
Specifications subject to change without notice
24 microhenries provides an inductive impedance of 270 ohms at a frequency of 1.8 MHz.
(multiply Inductance in microhenries by Frequency in megahertz by 6.28 to get Inductive Impedance in ohms)
*For a full explanation on how a balun works, see Chapter 9 of ŇTransmission Line Transformers" by Jerry Sevick, ISBN 1-884932-18-5
The cage material is 7" round X 1/4" thick white ABS plastic.
The cage dipole is a 1/2 wave in size aprox. 66' in length. Each side has 6 wires, held together with galvanized cable clamps, crimped with a copper sleeve and soldered, then covered with adhesive lined heat shrink. The 40 meter cage dipole has a bandwidth spread of almost 1 mhz. 3:1 and under.
The 40 meter cage dipole can be installed flat or inverted V, recommended height 25'. I did preform a test at center 12 feet off the ground, ends at 7 feet and it went flat 1:1 swr. The higher i went into the air the wider the bandwidth became. Remember: As with all antennas, be safe and use your head. Stay away from power lines and have a spotter around if you're on the roof or tower.
Returns Accepted for this item if it's within 14 Days