You must have javascript enabled to use antennasi.com !

LDG IT-100 Antenna tuner EXTENSION cable 50 ft 15M or 34.8 ft 10M for ICOM

radio

USD $79.95

Condition : New

Free Shipping

{{variant_type_name}} :
eBay
SKU: N/A This site contains affiliate links for which we may be compensated Consumer Electronics / Radio Communication / Parts & Accessories / Coax. Cables & Connectors

Notify me when the price drops

We will email you if we find a lower price on this product!

Target price (USD) $

High quality EXTENSION control cable for your IT-100 automatic antenna tuner. This extends the control cable that came with your IT-100 tuner to a compatible ICOM (with 4 pin Molex connector) radio Don't be fooled by cheap imitations! Buy GENUINE Radiodan quality!
Finally - take YOUR
wonderful IT-100 further away from your operating position!
For those who have an IT-100, you already know what a great tuner this is. The LDG IT-100 is perfect for tuning dipoles, beams, (ladder line fed with one of the LDG optional baluns), etc. You just need to be able to use the tuner further away than the OEM 36 INCH cable will allow!
Your OEM cable is only 36 inches long. How can you use that? (we sell OEM length replacements and a longer version in our Pricetronic store)
If you buy our 10M control cable extension version, then you should use  about 30-35 feet of coax (coax not included)
If you buy our 15M control cable extension version, then about 50 feet of coax would be perfect (coax not included)
WHY use a longer control cable? Why not just run more coax and tune inside the shack? Because long runs of coax when high SWR exists (before it gets to the tuner) exhibits MUCH higher loses due to additional feedline loss due to high SWR. Much more than the 50 ohm loss rating you see for coax in teh spec charts.
If you have a very high SWR (like 10:1, for example), you may have an additional 6-9 dB of loss in your coax! That would mean your 100 watts would be only 12.5 to 25 watts of radiated power!
Use CONTROL CABLE extensions whenever possible. By putting your tuner closer to the antenna feedpoint (be sure to properly weatherproof any tuner), you do not introduce additional SWR related feedline loss. Coax AFTER the tuner (to the radio) has NO additional loss due to SWR because the coax is carrying TUNED RF!
I use my LDG IT-100 at my base station with an IC-7100 and IC-7300 and I have one for portable as well. I had a need for a longer control cable and figured you do too!.
I only use the highest quality materials, ALL USA sourced! Four high quality 18 gauge stranded real copper wires, 100% shielded (foil) with shield runner wire that is tied to the black wire of the control cable at both ends. High quality USA source for ALL parts, cable, connector and pins. RUGGED Gray PVC jacket. Same wire jacket colors as OEM. Professionally crimped MOLEX M/F connectors with heat shrink tubing as shown.
If permanent use is desired, it is recommend to weatherproof the connection. Take your LDG IT-100 out in the field, add our cables to your GO KIT!  AS A BONUS, THIS CABLE ALSO WORKS WITH ICOM AH-4 (AH-3) ANTENNA TUNERS! Need a different length? Send me a message, we can custom make any length you desire. Need a replacement or longer IT-100 OEM cable? See our Pricetronic store Coax not included LDG tuner not included Radios not included Balun not included

Returns Accepted for this item if it's within 30 Days

LDG IT-100 Antenna tuner EXTENSION cable 50 ft 15M or 34.8 ft 10M for ICOM radio
mini whip antenna | antenna preamp | cisco at t microcell wireless cell signal booster tower antenna | nagoya antenna | antenna analyzers
See more
Price type
IN STOCK OUT STOCK